Microcat For Honda PDF Installation Instructions
Microcat can be installed to operate in a stand alone or network environment. Installations of Microcat require a dongle (hardware security key) to be connected to the appropriate computer port. If a dongle is not connected you may be required to select your region and country. Alternatively, Microcat Authorisation Server (MAS) can be used as the Microcat security measure. For more information on MAS, refer to the MAS installation and user guide posted on the MAS website: http://imassp.microcat.net/support.htm MAS must be used when operating Microcat in a thin client environment such as Terminal Services or Remote Desktop.
Honda 1100 ACE, AERO AND SABRE CenterStand PDF Installation Instruction
Relocation of Regulator
regulator. (finned aluminum box-approximately 3”x 4”) Note: See photo #1 – regulator already relocated. Remove the (2) 10 mm bolts attaching the regulator to the frame. Attach the bracket supplied to the regulator as shown. Using the original bolts, attach the regulator and bracket
assembly to the frame as shown in photo #1 using the two 10 mm bolts supplied.
Honda Accord Acura TL And TSX PDF Installation Instruction
INSTALLATION STEPS
1. Lower exhaust by removing two (2) rubber exhaust isolators for single exhaust vehicles and four (4) isolators for dual exhaust vehicles. (See RUBBER ISOLATOR REMOVAL DIAGRAM.)
2. Remove heat shield(s) by removing four (4) screws per shield. Save screws and shields for reinstallation in Step 8.
3. Check if hardware can be inserted through access holes in frame rails. If not, enlarge the holes with a die grinder or rotary tool until hardware can pass through.
4. Fishwire 7/16-14 x 1 1/2 carriage bolts and CM-SP11 spacers through access holes and out mounting holes in both frame rails, as shown. (See FISHWIRE TECHNIQUE diagram.)
5. Insert 3/8″ U-bolt through tow hook as shown.
6. Raise hitch into position and secure it with 7/16-14 hex flange nuts on to carriage bolts and 3/8-16 hex flange nuts on to U-bolt, as shown.
7. Torque all 7/16″ hardware to 50 lb-ft and 3/8″ hardware to 30 lb-ft.
8. Reinstall heat shields with hardware removed in Step 2. Trim heat shields around hitch. (See HEAT SHIELD TRIMMING DIAGRAM.)
Honda CRF PowerFlow kit with Inner Sealing Ring Installation Instructions
Step 1 – Remove OEM inner sealing ring, connection tube, and outside air boot sealing ring. Refer to owners manual.
Step 2 – Before installing Twin Air Inner Sealing Ring, apply a bead of silicone sealant into the machined groove on the Twin Air Inner Sealing Ring.
Step 3 – Install Twin Air Inner Sealing Ring into the airbox, attach air boot, and outer air boot sealing ring. Tighten nuts to clamp airbox together. Optional Twin Air Outer Sealing Ring Available (150212/150214 OSR)
Step 4 – When you are finished assembling the airbox, you need to cut off the rubber lip on the inside of the air boot.
Honda 650 Lift Kit Installation Instructions
This product is designed for use on ATVs on which additional ground clearance and fender clearance is desired. It is designed for utility type, slower-speed use on relatively flat terrain in deep mud or snow. Although we have many thousands of satisfied lift kit customers and over 400
franchised dealers selling and installing lift kits, purchasers should be aware that use of this product may increase the frequency of required maintenance, part wear, and will raise the center of gravity on your ATV increasing risk of roll-over on side hills, ditches or other steep terrain.
BMW Purchasing Strategy PDF Guide
BMW’s attractiveness as a partner has fallen markedly since the last BMW supplier satisfaction survey conducted in October 2003. The results of the February 2005 survey conclude that suppliers are losing trust in BMW and that the quality of communication between BMW and its suppliers has fallen. The major area of contention, according to our survey, is cost pressure. In the first survey BMW rated as one of the most attractive OEMs for suppliers to do business with. While on many counts the results for BMW have remained broadly similar, on that specific measure, BMW’s
attractiveness as a partner now rates more closely to that of DaimlerChrysler or Premier Automotive Group than Toyota.